Відео

what bolt did you use to hole the upper sheave on with? belt drive on the mixer side. mine had a small bolt but no washer or any thing that covered the sheave.

If you have a 400A service with 2 x 200A panels (with 200A circuit breaker on each panel), would you need two separate grounding systems, or one set of ground rods connect to both service panels?

Great advice, and a big help to me personally. I was just about to go rent a Bosch electric jackhammer to bust up a relatively small area of concrete walkway, but then I considered the sledgehammer option, which brought me to your video. After viewing it, I decided to buy a Husky 10-lb. sledgehammer at Home Depot... I put it to use today, and fairly easily busted up the slab (which was on average about 6" thick - thankfully with no re-bar in it). It helped that most of the slab was up-heaved due to some big, thick cedar tree roots that had worked their way underneath. I considered buying a smaller sledge while I was at Home Depot, but I'm glad I didn't: the 10-lb. sledge was just about the right fit for the job. Anything smaller would've been too wimpy, and anything heavier would not only have been overkill, but would've worn me out trying to wield the darned thing. Anyway, I now have a nice 10-lb. sledgehammer as part of my tool assortment. Not sure what I'll use it for next, but it is nice to know I've got one. Who knows, I might have use for it if the Zombie Apocalypse occurs.

Great instructional video. Finally able to put together my mixer after a lot of frustration and on the verge of returning it. The instructions that came bundled with the mixer are possibly the worst I've ever experienced.

DO YOU RECOMMEND RELIEF CUTS ALL THE WAY THROUGH?

My sister has a two story house with four bedroom. It was once a duplex but originally built in late 1800s the foundation are literally boulders. What kind of cost and time is she looking at?

Awesome thank you

I just had my drivers side Leaf Spring Shackle break. Pretty much rusted through. Great Video.

I would like lean for you .

Superb job! Thanks for your video! Will use the link to purchase the sensor right now 🙏

I read in a comment that you could have installed it upsidedown, that would have prevented the 4 gauge cables from traveling through the panel box and just directly into the lug entries, would have helped to avoid working around them every time you change something, I can see the merit in that comment

Thank you

So was your bare copper grounding wire 6 or 4 gauge?

Can you make more videos like this, please?

Was it worth it?

Good Instructional video. One question ,tho. Why not run the contaminated solvent into a container and not into the drain?

I would like to know the size of that block plz coz it's very nice

I thought it was illegal to mess with the meter. isn't that why the electric company puts that tamper seal on the meter box?

If is just 1 grounding rod, why did you get 2? Just curious.

Thank you for doing this. I wouldn’t have got it together without your help you’re right about what bolt to use where was pulling my hair out.

Could this connection/bonding of grounding conductor to neutral be done in the meterbase ?

Building my own house and about to compact my footer down with some powdery gravel. I think I will use a cheap jackhammer with a tamper bit.

Should you wet soil before you start to compact?

how many lighs can you hook up to the same motion sensor?

I have a short chain (german Forstkette) and hook it on that kind of winch line. That way the chain gets all sliding over the ground and the winch line just runs free.

FYI. You didn’t show the bolt that holds the wheel on after placing the key way

Thank you for the tutorial video; it was helpful. However, I have a question. Can you help me with it? I own a 2006 Dodge Dakota with a manual shift transmission. Recently, I replaced my transfer case output shaft. After a test drive, the truck shifted fine initially, but suddenly, it wouldn't move forward or backward. Could this be because I failed to mark the shift? Thanks.

Excellent video. Can I use a hammer drill instead of a demo hammer?

Really nice garage build. Got some inspirations from your build and feel excited about it. I am looking to do a DIY garage build like yours and will definitely come back to your videos for some ideas and inspirations. I have a question on about the boom. I'm interested in making a boom or buy one as I also have the Kubota sub compact tractor. Can I ask if you have a link to where you got the boom from or a plan for how to make that boom? Also, curious what's the HP on your tractor? My tractor is maxed out at 21 HP, it gives me a ball park on how heavy or how big I can make the boom. Thanks in advance. My children are still very young so what's really been holding me back is the additional help but that's about 7 years away before my oldest boy get bigger. For the time being, when I need an extra person to help, I have to schedule it with friends 🙂

Pour through/ knock out bond beams for first course, did you drill rebar in and knock the bond beams out add steel and pour?

Why did you not install a cut off switch while the power is off from the pole for servicing?

Thanks for the video. Question, I'm in Ohio where the frost line is 32 inches below grade. If I were to build a block workshed (probably 14ft x 14ft), would my trench and footer need to be 32 inches deep, and 16 inches wide around the perimeter?

Put a screw in the box to the wall

A friend used to clean his Glock by boiling it in distilled water for a deep clean. Anyone ever try that? This was in the early 90’s.

Really cool application for a 3D printer.

You Tube should remove this video due to everything is wrong with his install, this is a sub panel and the ground and neutral wire should separated. An inspector would red tag this job.

So many code violations just watching the first few seconds.

You not using green stud framing? Planing to do it again 😂😂😂

No moisture barrier between concrete and block?

If the rods don’t connect to anything else how does it complete a circuit? And what prevents the copper from corroding? Thanks

🥰 Thanks.

Much less waste than what the contractors will create! They’ll just replace the whole thing!

if that is the sub - panel which it looks like it is being i did not see the meter then your installation is wrong. On a sub panel the neutrals and grounds will be isolated from one another meaning your ECG conductor that entered that panel should have landed on a ground bar that was attached directly on the inside metal part of the panel.

Great video.. I have 2 electrical panels do I need to do this for both or can I connect both to one rod

You're a lucky guy to have a wife that works with you, wish I could say that.

Your pump support has a greater base than the jack stand does, why would you release the psi on it?

what a great video, and that is how you title a video like a real man without being retarded clickbait! Watch and learn, UA-camrs!! Thanks, Appalachian DIY!

Could I leave the old bushings in?

In the end you were talking about bonding the screw to the main panel, how did you do that?

Not sure you are right with one of your comments about return flow temp. The cooler the return is the more efficient your water heater runs. This is because the cooler the water is, the more energy/heat it will absorb as it flows through the heater for a given time. The bigger the temperature difference - the more heat is extracted/transferred from the heater to the water. You then use flow rate to manage the heated water temperature instead of the heater coming on and off all the time, if you are using a heat pump you absolutely want to keep the temperature gradient as large as possible with cooler return flows. Long pipe runs can however be a problem because of the reduced flow rate and reduced heat radiation as the water cools past a useful point on long runs - nothing to do with boiler efficiency.